Jump to content

Disassembly Advice


Recommended Posts

Hello All, 

 

I just bought the below sword at auction, and was hoping that someone could give some advice on disassembly? The pin seems to be an odd type, more similar to a screw to be honest, and is one I have not encountered before. 
 

Any advice? 
 

10922375-1CDC-46B1-8F81-17C43541169A.jpeg

F0E52C95-0906-4D38-B586-E640183EA7B0.jpeg

Link to comment
Share on other sites

The most obvious points in the limited photos you have provided are that all the crossings of the ito are in the same direction. If you look at an authentic Japanease sword, the  crossings will alternate. There are exceptions, but not very many. Instead of a bamboo mekugi what you see is a screw of the type seen on some WWII era gunto blades.

Link to comment
Share on other sites

The screw is what is normally seen on a Type 95 NCO gunto with aluminum handle (saya).  The fuchi (handle collar) is a close approximation of the Type 98 officer fuchi, but only close.  And while there are variations of the release button, I have never seen one with this pattern on it.  If you want more verification, please give us photos of the full sword, a clear shot of the blade and blade tip, and certainly remove the screw and take off the handle so we can see the nakago (tang).

 

You can buy the 2-prong driver tips at Ace Hardware, or I use a tool like this one to hold the nut while turning the other side with a normal screwdriver:

 

2 prong bit.jpg

20180831_084743.jpg

  • Like 2
Link to comment
Share on other sites

On 10/28/2021 at 9:59 AM, DTM72 said:

One would "normally" expect to find same' skin. (stingray)

Yes. I but I saw few swords with tsuka wrapped with other skins, snake and salmon with removed scales. I will try to found some photos

DSC06529.jpg

Edited by GrozaB
picture added
Link to comment
Share on other sites

Thank you all for the comments, I was able to get the pin out with the help of a jeweler but the handle still refuses to come off. I have tried both the traditional method and the wood block/hammer approach, but have not had any luck.

 

I was thinking about using some WD40 to loosen things up, but any alternative advice is much appreciated, regardless of if the blade is authentic or not. 
 

 

Link to comment
Share on other sites

It is a fake don't waste your time . If you must try,  wrap the blade ( so it is not damaged )  put it in a vice and then use a block of wood and hammer to hit the tsuba . When you have the handle off you will have discovered nothing other to confirm that what you have is a Chinese fake . My best advice is to move it on .

Ian Brooks

  • Like 2
Link to comment
Share on other sites

If it were my sword I would want to know as much as possible. Seeing the nakago is a crucial part of determining the origin of the blade.  If it is stuck, it’s simply rust. Get a rubber mallet and tap the hand guard until the handle and hand guard come off. I’ve done it numerous times. Sometimes the hand guard and spacers are simply fitted too snug.  You will not harm anything by forcing them off.

Link to comment
Share on other sites

This thread is quite old. Please consider starting a new thread rather than reviving this one, unless your post is really relevant and adds to the topic..

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...